Type 280 grinder loosen the rubber-steel-textile compound.
The loosened components are separated by means of magnetic-, air- and screening technology.
The textile fluff is very well suited as insulation material.
The separated steel wires have a purity of > 97 percent and can be lucratively sold.
This machine can cut the tire scraps into 2-20mesh small flakes
More questions, just contact us, we will suppli you professional support and solutions
]]>The batch type waste tire pyrolysis system is using strap conveyer, screw feeder and screw ash collector. Raw material will be heated and pyrolysis in reactor when it rotate. It has characteristic of short pyrolysis time, small labor intensity, low power consumption, catalyst-free and high safety factor. At same time, it resolve many problems of rotate type pyrolysis plant, such as too many airproof points, air pollution, oil vaper outlet and ash discharge outlet are easy to leak, etc. This batch type waste tire pyrolysis plant use original L type gas outlet, which can ensure raw material could be heated uniformly and pyrolysis completely, and also ensure the gas can be separated from carbon black powder efficiently. Compare to other plant’s problem that pyrolysis gas and carbon black always mixing together, output gas doesn’t has deposit and separate space, easy to jam pipeline and pollute oil by large amount carbon black powder, our plant has unexampled advantages. Furthermore, our batch type waste tire pyrolysis system install one waste heat recovery boiler inside to supply sufficient steam for the pyrolysis purpose, in the meanwhile, the WHRB utilizes the heat inside the flue gas so that the whole system heat loss is very low.
No. |
Name |
Model |
Unit |
Qty |
Power |
Remark |
1 |
Pyrolysis reactor |
Q/XF-III-5 |
set |
1 |
2.2kw |
XWYP2.2-117-3481-B3 |
2 |
Feed conveyor |
set |
1 |
2.2kw |
||
3 |
Spiral out of feeder |
Φ400Φ600-6 |
set |
1 |
2.2kw |
XWYP2.2-84-385-B3 |
4 |
Stove |
Φ1700×4000 |
set |
1 |
0.3kw |
RL-38 Burner |
5 |
Gas-liquid separation tower |
Φ630×2500 |
set |
1 |
||
6 |
Condenser |
Φ426×4000 |
set |
2 |
||
7 |
Circulating water pump |
IS65-50-160 |
set |
1 |
7.5kw |
Flow 30mh Head 32m |
8 |
Gear oil pump |
BCK-55 |
set |
1 |
1.5kw |
|
9 |
Fan |
Y5-47-5C |
set |
1 |
5.5kw |
|
10 |
Air Compressors |
set |
1 |
7.5kw |
||
11 |
Air preheater |
Φ530×4000 |
set |
1 |
||
12 |
Gas-liquid separator |
Φ800×1200 |
set |
1 |
||
13 |
Exhaust processor |
Φ800×1200 |
set |
1 |
||
14 |
Water Sealing |
Φ800×1200 |
set |
1 |
||
15 |
Intermediate tank |
Φ1200×1500 |
set |
1 |
||
16 |
Magnetic Pump |
160CQ-8 |
set |
2 |
0.75kw |
Lye pump |
17 |
Fuel Tank |
Φ1000×2000 |
set |
1 |
No. |
Name |
Model |
Unit |
Qty |
Power |
Remark |
1 |
Pyrolysis reactor |
Q/XF-III-5 |
set |
1 |
2.2kw |
XWYP2.2-117-3481-B3 |
2 |
Feed conveyor |
set |
1 |
2.2kw |
||
3 |
Spiral out of feeder |
Φ400Φ600-6 |
set |
1 |
2.2kw |
XWYP2.2-84-385-B3 |
4 |
Stove |
Φ1700×4000 |
set |
1 |
0.3kw |
RL-38 Burner |
5 |
Gas-liquid separation tower |
Φ630×2500 |
set |
1 |
||
6 |
Condenser |
Φ426×4000 |
set |
2 |
||
7 |
Circulating water pump |
IS65-50-160 |
set |
1 |
7.5kw |
Flow 30m h Head 32m |
8 |
Gear oil pump |
BCK-55 |
set |
1 |
1.5kw |
|
9 |
Fan |
Y5-47 -5C |
set |
1 |
5.5kw |
|
10 |
Air Compressors |
set |
1 |
7.5kw |
||
11 |
Air preheater |
Φ530×4000 |
set |
1 |
||
12 |
Gas-liquid separator |
Φ800×1200 |
set |
1 |
||
13 |
Exhaust processor |
Φ800×1200 |
set |
1 |
||
14 |
Water Sealing |
Φ800×1200 |
set |
1 |
||
15 |
Intermediate tank |
Φ1200×1500 |
set |
1 |
||
16 |
Magnetic Pump |
160CQ-8 |
set |
2 |
0.75kw |
Lye pump |
17 |
Fuel Tank |
Φ1000×2000 |
set |
1 |
This is rubber product making machine with column structure and downward pressing type, it is used to vulcanize all kinds of standard and non-standard rubber or plastic production, such as shoes sole, rubber plate, doormat and conveyer belt etc.
1. Stable pressure, good control in vulcanizing time and temperature
2. Automatic and manual operation system.
3. Reliable performance, stabile quality and good service.
4. Import /export right, Supply promptly quickly.
Type |
XLB-DQ850 × 60 0 × 4/2.5 |
Total Pressure(MN) |
2.5 |
Plate Size(mm) |
850 × 60 0 × 4 |
Daylight(mm) |
200 |
Daylight No |
4 |
Piston Stroke(mm) |
600 |
Unit Pressure(Mpa) |
50 |
Main Motor Power(kw) |
5.5 |
No. of hydraulic press |
1 |
Weight(kg) |
6000 |
Vacuum Compression Forming Machine, Vacuumize Shaper Vulcanizer, Plate Vulcanizing Product characteristics:
1. Multifunctional machine applicable for two-layer or three-layer mold
2. Fast mold open/close for high production efficiency, and slow clamp for mold protection
3. Automatic mold forward/backward and two-layer ejector for lower labour intensity;
4. Equipped with two pumps and two oil circuits with low noise, synchronous operation of two tables realizable;
5. PLC-controlled electrical system for easy operation;
6. Optional plate turnover mechanism which is more applicable for the processing of such products as valves and nipples;
7. Vacuumizing shortens cure time to improve quality and output;
8. Partial hydraulic components are genuine products from Germany, America and Taiwan.
Modle |
GHZD-200 |
GHZD-250 |
GHZD-300 |
Clamping Force(T) |
200 |
250 |
300 |
Cylinder Stroke(mm) |
300 |
300 |
300 |
Table Size(mm) |
500*500 |
600*600 |
650*650 |
Main Machine Power(KW) |
11 |
11 |
11 |
Opening Type |
Foward-ejector |
Foward-ejector |
Foward-ejector |
Double-bearing power(KW) |
25.6 |
28.8 |
32 |
Total Power(KW) |
38.8 |
41 |
45.2 |
Weight(T) |
11.4 |
12.3 |
13.8 |
Overall Dimension(mm) |
3250*3500*2600 |
3300*3500*2600 |
3500*3700*3600 |
Item:
CK 60 Series CNC Horizontal Lathe
Particular Function
1. CK 60 Series CNC Horizontal Lathe is designed by our company through many years’ practice. High cost-effective, low consumption
2. According to the prepared operation program, the two coordinates CNC system automatically finish the processing of complex curved surface, such as inner bore, external circle, mold cavity, cone and so on.
3. Mainly used in cutting the heavy plate-like and ring-like machine parts with bigger diameter. It is widely used in the processing of rubber machine, heavy machine, automobile production, mining machine and railway equipment parts.
The Main Technical Parameters Please refer to the following enclosed Form.
To get more detail and accuracy information, please feel free to contact with me.
Type of Machine Tool | CK6020 | CK6014 | |
Central height above the foundation (mm) | 1010 | 730 | |
Rotary Dia. of Largest Work – piece (mm) | 2000 | 1400 | |
Length of Largest Work – piece (mm) | 450 | 380 | |
Height above the large trailing bar ( mm) | 390 | 350 | |
Maximum Bearing (t ) | 3 | 1.5 | |
Rotary Speed of Principal Axis (r/min) | 0~100 | 0~140 | |
Rotary angle of knife rest | 360° | 360° | |
Maximum horizontal moving stroke of knife rest (mm) | 800 | 700 | |
Maximum vertical moving stroke of knife rest (mm) | 460 | 380 | |
Type of main motor | Y160L-6 ,15KW | Y160L-6, 11KW | |
Type of supply motor | 130BYG250A | 130BYG250A | |
Type of NC system | WA-21DT | WA-21DT | |
Type of lubricant pump | YB01A | YB01A | |
External Dimension (mm * mm * mm ) | 3500 × 2140 × 2032 | 3292 × 1817 × 1620 | |
Total weight of Machine Tool ( t ) | 7.6 | 5.8 | |
Work Precision | Culindercity | 500 : 0.03 | |
Roundness | ≤0.02 | ||
Flatness | Above 500mm is 0.02mm |
Be used for the mastication, mixing, warming up and sheeting of rubber.
Specification | XK-660 | XK-710 |
Roll diameter: | φ660mm (26″) | φ710mm (28″) |
Working length of the rolls: | 2130mm (84″) | 2200mm (87″) |
Structure of front roll: | bored roll or drilled roll or fluted roll | bored roll or drilled roll |
Linear velocity of the front roll: | 28.6/32.53m/min | 3~30m/min |
Friction ratio of rolls: | 1:1.09 / 1:1.24 | 1:1.083 |
Material of rolls: | chilled cast iron | chilled cast iron |
Hardness of rolls: | HS68~75 | HS68~75 |
Max. nip of rolls: | 15mm | 17mm |
Bush: | bearing type | bearing type |
Feeding capacity per batch: | 165Kg | 210Kg |
Motor power: | 180/245KW | 280KW |
Voltage1: | 420V, 50HZ, 3 phrase; | 380~440V, 50HZ, 3 phrase; |
Voltage2: | 220V, 50HZ, single phrase with transformer | 220V, 50HZ, single phrase with transformer |
HE-EP pyrolysis technology integrated features:
1. Technologically advanced: A small investment; Small footprint
2. Plant construction land 300m2 ~ 2500m2;
3. Low running costs: The high level of automation equipment, daily classes 3 to 6 people;
4. Short cycle: The standardization of building-block design, in 20 ~ 40 days to complete the installation, commissioning, turn-key operation (not including plant construction time);
5. Refining a wide range of raw materials, inexhaustible;
6. Advanced furnace room, installation, demolition fast, easy maintenance;
7. Equipment technology advanced, fast pyrolysis, the oil is high, all-weather continuous production, without having to wait for furnace cooling, you can tap, feed, improved production efficiency. The use of electricclosed quickly, sealing, security.
8. Using patented catalyst cracking, cracking fast Chunqing oil. Oil collection system with multi-stage cooling system to ensure adequate oil and gas cooling rates and higher oil;
9. Security, closed pyrolysis reactor, set combustion, heat decomposition for the integration of design, high-temperature combustion gas channel in the composite cyclone rotary heating, so that a significant increase heating efficiency, reduce heat and improve the efficiency of the endothermic pyrolysis reactor, reduce the cost of consumption of combustion is the core technology of the system.
Resources
10. Loop of the economy: Round-the-clock production equipment, closed-end clean running oil-producing fast, good oil quality, save fuel, the combustion by a pyrolysis oil, pure oil quality, purity is close to diesel oil, no smell, the burning of high value; General integrated waste oil rate of 25 ~ 50%; Tires, waste rubber oil rate of 35 ~ 40%; Waste oil and other oil rates up to 70 ~ 85%; By secondary cracking of diesel oil, high purity, after pyrolysis in an oil based on the combustion of oil rate of 85 ~ 90%, after chemical treatment, up to the standard 0 # diesel oil, the oil power, and resistant to combustion, the engine without any side effects.
11. Energy reduction: In the pyrolysis process, the oil and gas will be produced for a large number of normal temperature and pressure can not be liquefied combustible gas (methane-butane), which treated gas through the gas nozzle is designed with the full combustion in the furnace, a large amount of heat, not only significantly save energy, but also greatly improved the production efficiency. Combustion of soot, smoke and dust treatment system by the discharge, no secondary pollution, emissions to meet national standards.
12. Provide for cracking waste rubber, waste plastics, tires and all kinds of waste lubricating oil hydrogenation transfer agents, catalysts, depigmenting agents, sweetening agents, can be refined 90 # gasoline, 0 # diesel oil were to reach the national standard.
13. The whole process of computer control of materials, recycling of water temperature, reactor temperature, feed, spoil disposal, transportation of oil products, as well as the process of failure alarm systems, real-time detection, control and stable operation. Significantly reduce the manual operations, improve security, reduce the auxiliary time, the protection of the safe operation, increasing productivity.
]]>Process flow:
Waste tyre–cutting loop mouth–cutting strip–cutting dice crushing filtering–magnetic separating filtering–finished products
Processing method:
Physic mechanical crushing method at normal temperature of waste tyre: Nochemical raw material is required, no waste gas, washte water and soot are discharged, and the cooling water of the equipment is reused, no emission, equipment noise is within the range specified by the country(GB20055-2006), fineness of rubber powder produced by it is adjustable(10 meshes to 30 meshes), take waste tyre as example, the process is as follows: Breaking down, crushing, filtering, magnetic separating, grin-ding, then the finished products are produced.
1. Tyre bead ring cutting off machine
This machine mian to cut the inner dimater of the tyre, and cut the side of the tyre to the next step of segmentation.
]]>The machine is used to produce strip precured tread for renovation of all kinds of tires. And is suitable for cold renovation procedure of tires.
We can supply press with platen size 4100*350, 4600*540, 6600*510, 4000*700, 3800*360
5500*360, 3800*700, total pressure 400t, 650t, 750t, 900t, 1100t, and other models according to the requirements of the buyer.
Please contact us if you feel free.
]]>Hose cutting machine
1. Hose size: 6mm~51mm
2. Power: 2.2kw
3. Working voltage: 380V/220V
4. Diameter of blades: 300mm
5. Weight: 80kgs
6. Measurement: 650*550*850mm
]]>